Skip to main content

Calculating subnets with VLSM

Calculating subnets with VLSM

 1.1.4 VLSM helps to manage IP addresses. This page will explain how to use VLSM to set subnet masks that fit the link or segment requirements. A subnet mask should satisfy the requirements of a LAN with one subnet mask and the requirements of a point-to-point WAN with another. 
The example in Figure shows a network that requires an address scheme.
The example contains a Class B address of 172.16.0.0 and two LANs that require at least 250 hosts each. If the routers use a classful routing protocol, the WAN link must be a subnet of the same Class B network. Classful routing protocols such as RIP v1, IGRP, and EGP do not support VLSM. Without VLSM, the WAN link would need the same subnet mask as the LAN segments. A 24-bit mask of 255.255.255.0 can support 250 hosts.  
The WAN link only needs two addresses, one for each router. That means that 252 addresses would be wasted.
If VLSM was used, a 24-bit mask would still be applied on the LAN segments for the 250 hosts. A 30-bit mask could be used for the WAN link because only two host addresses are needed.
Figure shows where the subnet addresses can be applied based on the number of host requirements. The WAN links use subnet addresses with a prefix of /30. This prefix allows for only two host addresses which is just enough for a point-to-point connection between a pair of routers.
In Figure , the subnet addresses used are generated when the 172.16.32.0/20 subnet is divided into /26 subnets.
To calculate the subnet addresses used on the WAN links, further subnet one of the unused /26 subnets. In this example, 172.16.33.0/26 is further subnetted with a prefix of /30. This provides four more subnet bits and therefore 16 (24) subnets for the WANs. Figure illustrates how to work through a VLSM system.
VLSM can be used to subnet an already subnetted address. For example, consider the subnet address 172.16.32.0/20 and a network that needs ten host addresses. With this subnet address, there are 212 – 2, or 4094 host addresses, most of which will be wasted. With VLSM it is possible to subnet 172.16.32.0/20 to create more network addresses with fewer hosts per network. When 172.16.32.0/20 is subnetted to 172.16.32.0/26, there is a gain of 26, or 64 subnets. Each subnet can support 26 – 2, or 62 hosts.
Use the following steps to apply VLSM to 172.16.32.0/20:
  1. Write 172.16.32.0 in binary form.
  2. Draw a vertical line between the 20th and 21st bits, as shown in Figure . The original subnet boundary was /20.
  3. Draw a vertical line between the 26th and 27th bits, as shown in Figure . The original /20 subnet boundary is extended six bits to the right, which becomes /26.
  4. Calculate the 64 subnet addresses with the bits between the two vertical lines, from lowest to highest in value. The figure shows the first five subnets available.
It is important to remember that only unused subnets can be further subnetted. If any address from a subnet is used, that subnet cannot be further subnetted. In Figure , four subnet numbers are used on the LANs. The unused 172.16.33.0/26 subnet is further subnetted for use on the WAN links.
The Lab Activity will help students calculate VLSM subnets.
The next page will describe route aggregation.

Comments

Post a Comment

Popular posts from this blog

OSI layers / Peer-to-peer communications / TCP/IP model

OSI layers 2.3.4 This page discusses the seven layers of the OSI model. The OSI reference model is a framework that is used to understand how information travels throughout a network. The OSI reference model explains how packets travel through the various layers to another device on a network, even if the sender and destination have different types of network media. In the OSI reference model, there are seven numbered layers, each of which illustrates a particular network function. - Dividing the network into seven layers provides the following advantages: • It breaks network communication into smaller, more manageable parts. • It standardizes network components to allow multiple vendor development and support. • It allows different types of network hardware and software to communicate with each other. • It prevents changes in one layer from affecting other layers. • It divides network communication into smaller parts to make learning it easier to understand. In the foll...
Post a Comment
Read more

Advantages and disadvantages of link-state routing

Advantages and disadvantages of link-state routing 2.1.5  This page lists the advantages and disadvantages of link-state routing protocols. The following are advantages of link-state routing protocols:  Link-state protocols use cost metrics to choose paths through the network. The cost metric reflects the capacity of the links on those paths. Link-state protocols use triggered updates and LSA floods to immediately report changes in the network topology to all routers in the network. This leads to fast convergence times. Each router has a complete and synchronized picture of the network. Therefore, it is very difficult for routing loops to occur. Routers use the latest information to make the best routing decisions. The link-state database sizes can be minimized with careful network design. This leads to smaller Dijkstra calculations and faster convergence. Every router, at the very least, maps the topology of it...
Post a Comment
Read more

Ports for services

Ports for services 10.2.2  Services running on hosts must have a port number assigned to them so communication can occur. A remote host attempting to connect to a service expects that service to use specific transport layer protocols and ports. Some ports, which are defined in RFC 1700, are known as the well-known ports. These ports are reserved in both TCP and UDP.  These well-known ports define applications that run above the transport layer protocols. For example, a server that runs FTP will use ports 20 and 21 to forward TCP connections from clients to its FTP application. This allows the server to determine which service a client requests. TCP and UDP use port numbers to determine the correct service to which requests are forwarded. The next page will discuss ports in greater detail.
Post a Comment
Read more