1900/2950 password recovery / 1900/2950 firmware upgrade

1900/2950 password recovery
6.2.8 For security and management purposes, passwords must be set on the console and vty lines. An enable password and an enable secret password must also be set. These practices help ensure that only authorized users have access to the User and Privileged EXEC modes of the switch.
There will be circumstances where physical access to the switch can be achieved, but access to the User or Privileged EXEC mode cannot be gained because the passwords are not known or have been forgotten.
In these circumstances, a password recovery procedure must be followed.
The Lab Activities will show students how to recover a password on a Catalyst 2900 series switch.

1900/2950 Firmware Upgrade
6.2.9 This page will explain the purpose of IOS and firmware upgrades and how they are performed.
IOS and firmware images are periodically released with bugs fixes, new features, and performance improvements. If the network can be made more secure, or can operate more efficiently with a new version of the IOS, then the IOS should be upgraded.
To upgrade the IOS, download a copy of the new image to a local server from the Cisco Connection Online (CCO) Software Center.
The Lab Activities will show students how to upgrade the firmware of a switch.
This page concludes this lesson. The next page will summarize the main points from this module.

Comments

OSI layers / Peer-to-peer communications / TCP/IP model

OSI layers 2.3.4 This page discusses the seven layers of the OSI model. The OSI reference model is a framework that is used to understand how information travels throughout a network. The OSI reference model explains how packets travel through the various layers to another device on a network, even if the sender and destination have different types of network media. In the OSI reference model, there are seven numbered layers, each of which illustrates a particular network function. - Dividing the network into seven layers provides the following advantages: • It breaks network communication into smaller, more manageable parts. • It standardizes network components to allow multiple vendor development and support. • It allows different types of network hardware and software to communicate with each other. • It prevents changes in one layer from affecting other layers. • It divides network communication into smaller parts to make learning it easier to understand. In the foll...

PC Basic...

• Backplane – A backplane is an electronic circuit board containing circuitry and sockets into which additional electronic devices on other circuit boards or cards can be plugged; in a computer, generally synonymous with or part of the motherboard. • Network interface card (NIC) – An expansion board inserted into a computer so that the computer can be connected to a network. • Video card – A board that plugs into a PC to give it display capabilities. • Audio card – An expansion board that enables a computer to manipulate and output sounds. • Parallel port – An interface capable of transferring more than one bit simultaneously that is used to connect external devices such as printers. • Serial port – An interface that can be used for serial communication in which only one bit is transmitted at a time. • Mouse port – A port used to connect a mouse to a PC. • USB port – A Universal Serial Bus connector. A USB port connects devices such as a mouse or printer to the computer ...

1.2.2 RIP V2 Features

1.2.2 RIP V2 Features This page will discuss RIP v2, which is an improved version of RIP v1. Both versions of RIP share the following features: It is a distance vector protocol that uses a hop count metric. It uses hold down timers to prevent routing loops – default is 180 seconds. It uses split horizon to prevent routing loops. It uses 16 hops as a metric for infinite distance. RIP v2 provides prefix routing, which allows it to send out subnet mask information with the route update. Therefore, RIP v2 supports the use of classless routing in which different subnets within the same network can use different subnet masks, as in VLSM. RIP v2 provides for authentication in its updates. A set of keys can be used on an interface as an authentication check. RIP v2 allows for a choice of the type of authentication to be used in RIP v2 packets. The choice can be either clear text or Message-Digest 5 (MD5) encryption. Clear text is the default. MD5 can be used t...

CCNA :) Be a Good Network Administrator

Search This Blog