Skip to main content

How ACLs work

How ACLs work 
11.1.2 An ACL is made up of statements that define whether packets are accepted or rejected at inbound and outbound interfaces. This page will explain how these statements are edited and added to an ACL. These decisions are made by matching a condition statement in an access list and then performing the accept or reject action defined in the statement.
The order in which ACL statements are placed is important. The Cisco IOS software tests the packet against each condition statement in order from the top of the list to the bottom. Once a match is found in the list, the accept or reject action is performed and no other ACL statements are checked. If a condition statement that permits all traffic is located at the top of the list, no statements added below that will ever be checked.
If additional condition statements are needed in an access list, the entire ACL must be deleted and recreated with the new condition statements. To make the process of revising an ACL simpler it is a good idea to use a text editor such as Notepad and paste the ACL into the router configuration.
The beginning of the router process is the same, whether ACLs are used or not. As a frame enters an interface, the router checks to see whether the Layer 2 address matches or if it is a broadcast frame. If the frame address is accepted, the frame information is stripped off and the router checks for an ACL on the inbound interface. If an ACL exists, the packet is now tested against the statements in the list. If the packet matches a statement, the packet is either accepted or rejected. If the packet is accepted in the interface, it will then be checked against routing table entries to determine the destination interface and switched to that interface. Next, the router checks whether the destination interface has an ACL. If an ACL exists, the packet is tested against the statements in the list. If the packet matches a statement, it is either accepted or rejected. If there is no ACL or the packet is accepted, the packet is encapsulated in the new Layer 2 protocol and forwarded out the interface to the next device.
As a review, ACL statements operate in sequential, logical order. If a condition match is true, the packet is permitted or denied and the rest of the ACL statements are not checked. If all the ACL statements are unmatched, an implicit deny any statement is placed at the end of the list by default. The invisible deny any statement at the end of the ACL will not allow unmatched packets to be accepted. When first learning how to create ACLs, it is a good idea to add the deny any at the end of ACLs to reinforce the dynamic presence of the implicit deny.
The next page will describe how ACLs are created

Comments

Post a Comment

Popular posts from this blog

Windowing

Windowing 11.1.5 This page will explain how windows are used to transmit data. Data packets must be delivered to the recipient in the same order in which they were transmitted to have a reliable, connection-oriented data transfer. The protocol fails if any data packets are lost, damaged, duplicated, or received in a different order. An easy solution is to have a recipient acknowledge the receipt of each packet before the next packet is sent. If a sender had to wait for an ACK after each packet was sent, throughput would be low. Therefore, most connection-oriented, reliable protocols allow multiple packets to be sent before an ACK is received. The time interval after the sender transmits a data packet and before the sender processes any ACKs is used to transmit more data. The number of data packets the sender can transmit before it receives an ACK is known as the window size, or window. TCP uses expectational ACKs. This means that the ACK number refers to the next packet that is...
Post a Comment
Read more

OSI layers / Peer-to-peer communications / TCP/IP model

OSI layers 2.3.4 This page discusses the seven layers of the OSI model. The OSI reference model is a framework that is used to understand how information travels throughout a network. The OSI reference model explains how packets travel through the various layers to another device on a network, even if the sender and destination have different types of network media. In the OSI reference model, there are seven numbered layers, each of which illustrates a particular network function. - Dividing the network into seven layers provides the following advantages: • It breaks network communication into smaller, more manageable parts. • It standardizes network components to allow multiple vendor development and support. • It allows different types of network hardware and software to communicate with each other. • It prevents changes in one layer from affecting other layers. • It divides network communication into smaller parts to make learning it easier to understand. In the foll...
Post a Comment
Read more

1.2.2 RIP V2 Features

 1.2.2 RIP V2 Features This page will discuss RIP v2, which is an improved version of RIP v1. Both versions of RIP share the following features: It is a distance vector protocol that uses a hop count metric. It uses hold down timers to prevent routing loops – default is 180 seconds. It uses split horizon to prevent routing loops. It uses 16 hops as a metric for infinite distance. RIP v2 provides prefix routing, which allows it to send out subnet mask information with the route update. Therefore, RIP v2 supports the use of classless routing in which different subnets within the same network can use different subnet masks, as in VLSM. RIP v2 provides for authentication in its updates. A set of keys can be used on an interface as an authentication check. RIP v2 allows for a choice of the type of authentication to be used in RIP v2 packets. The choice can be either clear text or Message-Digest 5 (MD5) encryption. Clear text is the default. MD5 can be used t...
Post a Comment
Read more