Skip to main content

2.1.2 WAN devices / 2.1.3 WAN Standards

2.1.2 WAN devices
WANs are groups of LANs connected together with communications links from a service provider. Because the communications links cannot plug directly into the LAN, it is necessary to identify the various pieces of interfacing equipment.
LAN-based computers with data to transmit send data to a router that contains both LAN and WAN interfaces. The router will use the Layer 3 address information to deliver the data on the appropriate WAN interface. Routers are active and intelligent network devices and therefore can participate in network management. Routers manage networks by providing dynamic control over resources and supporting the tasks and goals for networks. Some of these goals are connectivity, reliable performance, management control, and flexibility.
The communications link needs signals in an appropriate format. For digital lines, a channel service unit (CSU) and a data service unit (DSU) are required. The two are often combined into a single piece of equipment, called the CSU/DSU. The CSU/DSU may also be built into the interface card in the router.
A modem is needed if the local loop is analog rather than digital. Modems transmit data over voice-grade telephone lines by modulating and demodulating the signal. The digital signals are superimposed on an analog voice signal that is modulated for transmission. The modulated signal can be heard as a series of whistles by turning on the internal modem speaker. At the receiving end the analog signals are returned to their digital form, or demodulated.
When ISDN is used as the communications link, all equipment attached to the ISDN bus must be ISDN-compatible. Compatibility is generally built into the computer interface for direct dial connections, or the router interface for LAN to WAN connections. Older equipment without an ISDN interface requires an ISDN terminal adapter (TA) for ISDN compatibility.
Communication servers concentrate dial-in user communication and remote access to a LAN. They may have a mixture of analog and digital (ISDN) interfaces and support hundreds of simultaneous users.
WAN Standards
2.1.3
WANs use the OSI reference model, but focus mainly on Layer 1 and Layer 2. WAN standards typically describe both physical layer delivery methods and data link layer requirements, including physical addressing, flow control, and encapsulation. WAN standards are defined and managed by a number of recognized authorities.
The physical layer protocols describe how to provide electrical, mechanical, operational, and functional connections to the services provided by a communications service provider. Some of the common physical layer standards are listed in Figure , and their connectors illustrated in Figure .
The data link layer protocols define how data is encapsulated for transmission to remote sites, and the mechanisms for transferring the resulting frames. A variety of different technologies are used, such as ISDN, Frame Relay or Asynchronous Transfer Mode (ATM). These protocols use the same basic framing mechanism, high-level data link control (HDLC), an ISO standard, or one of its sub-sets or variants.

Comments

Post a Comment

Popular posts from this blog

Windowing

Windowing 11.1.5 This page will explain how windows are used to transmit data. Data packets must be delivered to the recipient in the same order in which they were transmitted to have a reliable, connection-oriented data transfer. The protocol fails if any data packets are lost, damaged, duplicated, or received in a different order. An easy solution is to have a recipient acknowledge the receipt of each packet before the next packet is sent. If a sender had to wait for an ACK after each packet was sent, throughput would be low. Therefore, most connection-oriented, reliable protocols allow multiple packets to be sent before an ACK is received. The time interval after the sender transmits a data packet and before the sender processes any ACKs is used to transmit more data. The number of data packets the sender can transmit before it receives an ACK is known as the window size, or window. TCP uses expectational ACKs. This means that the ACK number refers to the next packet that is...
Post a Comment
Read more

OSI layers / Peer-to-peer communications / TCP/IP model

OSI layers 2.3.4 This page discusses the seven layers of the OSI model. The OSI reference model is a framework that is used to understand how information travels throughout a network. The OSI reference model explains how packets travel through the various layers to another device on a network, even if the sender and destination have different types of network media. In the OSI reference model, there are seven numbered layers, each of which illustrates a particular network function. - Dividing the network into seven layers provides the following advantages: • It breaks network communication into smaller, more manageable parts. • It standardizes network components to allow multiple vendor development and support. • It allows different types of network hardware and software to communicate with each other. • It prevents changes in one layer from affecting other layers. • It divides network communication into smaller parts to make learning it easier to understand. In the foll...
Post a Comment
Read more

1.2.2 RIP V2 Features

 1.2.2 RIP V2 Features This page will discuss RIP v2, which is an improved version of RIP v1. Both versions of RIP share the following features: It is a distance vector protocol that uses a hop count metric. It uses hold down timers to prevent routing loops – default is 180 seconds. It uses split horizon to prevent routing loops. It uses 16 hops as a metric for infinite distance. RIP v2 provides prefix routing, which allows it to send out subnet mask information with the route update. Therefore, RIP v2 supports the use of classless routing in which different subnets within the same network can use different subnet masks, as in VLSM. RIP v2 provides for authentication in its updates. A set of keys can be used on an interface as an authentication check. RIP v2 allows for a choice of the type of authentication to be used in RIP v2 packets. The choice can be either clear text or Message-Digest 5 (MD5) encryption. Clear text is the default. MD5 can be used t...
Post a Comment
Read more