Skip to main content

A waste of space

A waste of space
1.1.2 This page will explain how certain address schemes can waste address space.
In the past, the first and last subnet were not supposed to be used. The use of the first subnet, which was known as subnet zero, was discouraged because of the confusion that could occur if a network and a subnet had the same address. This also applied to the use of the last subnet, which was known as the all-ones subnet. With the evolution of network technologies and IP address depletion, the use of the first and last subnets have become an acceptable practice in conjunction with VLSM.
In Figure , the network management team has borrowed three bits from the host portion of the Class C address that has been selected for this address scheme.
If the team decides to use subnet zero, there will be eight useable subnets. Each subnet can support 30 hosts. If the team decides to use the no ip subnet-zero command, there will be seven usable subnets with 30 hosts in each subnet. Cisco routers with Cisco IOS version 12.0 or later, use subnet zero by default.
In Figure , the Sydney, Brisbane, Perth, and Melbourne remote offices may each have 30 hosts. The team realizes that it has to address the three point-to-point WAN links between Sydney, Brisbane, Perth, and Melbourne. If the team uses the last three subnets for the WAN links, all of the available addresses will be used and there will be no room for growth. The team will also have wasted the 28 host addresses from each subnet to simply address three point-to-point networks. This address scheme would waste one-third of the potential address space.
Such an address scheme is fine for a small LAN. However, it is extremely wasteful if point-to-point connections are used.
The next page will explain how VLSM can be used to prevent wasted addresses.

Comments

Post a Comment

Popular posts from this blog

OSI layers / Peer-to-peer communications / TCP/IP model

OSI layers 2.3.4 This page discusses the seven layers of the OSI model. The OSI reference model is a framework that is used to understand how information travels throughout a network. The OSI reference model explains how packets travel through the various layers to another device on a network, even if the sender and destination have different types of network media. In the OSI reference model, there are seven numbered layers, each of which illustrates a particular network function. - Dividing the network into seven layers provides the following advantages: • It breaks network communication into smaller, more manageable parts. • It standardizes network components to allow multiple vendor development and support. • It allows different types of network hardware and software to communicate with each other. • It prevents changes in one layer from affecting other layers. • It divides network communication into smaller parts to make learning it easier to understand. In the foll...
Post a Comment
Read more

PC Basic...

• Backplane – A backplane is an electronic circuit board containing circuitry and sockets into which additional electronic devices on other circuit boards or cards can be plugged; in a computer, generally synonymous with or part of the motherboard. • Network interface card (NIC) – An expansion board inserted into a computer so that the computer can be connected to a network. • Video card – A board that plugs into a PC to give it display capabilities. • Audio card – An expansion board that enables a computer to manipulate and output sounds. • Parallel port – An interface capable of transferring more than one bit simultaneously that is used to connect external devices such as printers. • Serial port – An interface that can be used for serial communication in which only one bit is transmitted at a time. • Mouse port – A port used to connect a mouse to a PC. • USB port – A Universal Serial Bus connector. A USB port connects devices such as a mouse or printer to the computer ...
Post a Comment
Read more

1.2.2 RIP V2 Features

 1.2.2 RIP V2 Features This page will discuss RIP v2, which is an improved version of RIP v1. Both versions of RIP share the following features: It is a distance vector protocol that uses a hop count metric. It uses hold down timers to prevent routing loops – default is 180 seconds. It uses split horizon to prevent routing loops. It uses 16 hops as a metric for infinite distance. RIP v2 provides prefix routing, which allows it to send out subnet mask information with the route update. Therefore, RIP v2 supports the use of classless routing in which different subnets within the same network can use different subnet masks, as in VLSM. RIP v2 provides for authentication in its updates. A set of keys can be used on an interface as an authentication check. RIP v2 allows for a choice of the type of authentication to be used in RIP v2 packets. The choice can be either clear text or Message-Digest 5 (MD5) encryption. Clear text is the default. MD5 can be used t...
Post a Comment
Read more