Skip to main content

Route aggregation with VLSM

 Route aggregation with VLSM

1.1.5 

When VLSM is used, it is important to keep the subnetwork numbers grouped together in the network to allow for aggregation. For example, networks like 172.16.14.0 and 172.16.15.0 should be near one another so that the routers only carry a route for 172.16.14.0/23.

The use of classless interdomain routing (CIDR) and VLSM prevents address waste and promotes route aggregation, or summarization. Without route summarization, Internet backbone routing would likely have collapsed sometime before 1997.

Figure illustrates how route summarization reduces the burden on upstream routers. This complex hierarchy of variable-sized networks and subnetworks is summarized at various points with a prefix address, until the entire network is advertised as a single aggregate route of 200.199.48.0/20. Route summarization, or supernetting, is only possible if the routers of a network use a classless routing protocol, such as OSPF or EIGRP. Classless routing protocols carry a prefix that consists of a 32-bit IP address and bit mask in the routing updates. In Figure , the summary route that eventually reaches the provider contains a 20-bit prefix common to all of the addresses in the organization. That address is 200.199.48.0/22 or 11001000.11000111.0011. For summarization to work, addresses should be carefully assigned in a hierarchical fashion so that summarized addresses will share the same high-order bits.

The following are important rules to remember:

  • A router must know in detail the subnet numbers attached to it.
  • A router does not need to inform other routers about each subnet if the router can send one aggregate route for a set of routes.
  • A router that uses aggregate routes has fewer entries in its routing table.

VLSM increases route summarization flexibility because it uses the higher-order bits shared on the left, even if the networks are not contiguous.

Figure shows that the addresses share the first 20 bits. These bits are colored red. The 21st bit is not the same for all the routes. Therefore the prefix for the summary route will be 20 bits long. This is used to calculate the network number of the summary route.

Figure shows that the addresses share the first 21 bits. These bits are colored red. The 22nd bit is not the same for all the routes. Therefore the prefix for the summary route will be 21 bits long. This is used to calculate the network number of the summary route.

The next page will teach students how to configure VLSM.



Comments

Post a Comment

Popular posts from this blog

OSI layers / Peer-to-peer communications / TCP/IP model

OSI layers 2.3.4 This page discusses the seven layers of the OSI model. The OSI reference model is a framework that is used to understand how information travels throughout a network. The OSI reference model explains how packets travel through the various layers to another device on a network, even if the sender and destination have different types of network media. In the OSI reference model, there are seven numbered layers, each of which illustrates a particular network function. - Dividing the network into seven layers provides the following advantages: • It breaks network communication into smaller, more manageable parts. • It standardizes network components to allow multiple vendor development and support. • It allows different types of network hardware and software to communicate with each other. • It prevents changes in one layer from affecting other layers. • It divides network communication into smaller parts to make learning it easier to understand. In the foll...
Post a Comment
Read more

Advantages and disadvantages of link-state routing

Advantages and disadvantages of link-state routing 2.1.5  This page lists the advantages and disadvantages of link-state routing protocols. The following are advantages of link-state routing protocols:  Link-state protocols use cost metrics to choose paths through the network. The cost metric reflects the capacity of the links on those paths. Link-state protocols use triggered updates and LSA floods to immediately report changes in the network topology to all routers in the network. This leads to fast convergence times. Each router has a complete and synchronized picture of the network. Therefore, it is very difficult for routing loops to occur. Routers use the latest information to make the best routing decisions. The link-state database sizes can be minimized with careful network design. This leads to smaller Dijkstra calculations and faster convergence. Every router, at the very least, maps the topology of it...
Post a Comment
Read more

PC Basic...

• Backplane – A backplane is an electronic circuit board containing circuitry and sockets into which additional electronic devices on other circuit boards or cards can be plugged; in a computer, generally synonymous with or part of the motherboard. • Network interface card (NIC) – An expansion board inserted into a computer so that the computer can be connected to a network. • Video card – A board that plugs into a PC to give it display capabilities. • Audio card – An expansion board that enables a computer to manipulate and output sounds. • Parallel port – An interface capable of transferring more than one bit simultaneously that is used to connect external devices such as printers. • Serial port – An interface that can be used for serial communication in which only one bit is transmitted at a time. • Mouse port – A port used to connect a mouse to a PC. • USB port – A Universal Serial Bus connector. A USB port connects devices such as a mouse or printer to the computer ...
Post a Comment
Read more