Skip to main content

Disconnecting and suspending Telnet sessions

Disconnecting and suspending Telnet sessions


4.2.3 This page will introduce two important features of the telnet command. These are the disconnect feature and the suspend feature.
A potential problem exists when a Telnet session is suspended and the Enter key is pressed. Cisco IOS software resumes the connection to the most recently suspended Telnet connection. The Enter key is used frequently. With a suspended Telnet session, it is possible to reconnect to another router. This is dangerous when changes are made to the configuration or EXEC commands are used. Always check which router is connected when the suspended Telnet feature is used.
The show sessions command will show which Telnet sessions are active.
The procedure that is used to disconnect a Telnet session is as follows:
  • Enter the disconnect command.
  • Follow the command with the name or IP address of the router or the session number. An example is as follows:
Denver>disconnect paris
The procedure that is used to suspend a Telnet session is as follows:
  • Press Ctrl-Shift-6, then x.
  • Enter the name of the router or IP address.
The Lab Activity will instruct students on how to suspend a Telnet session.
The next page will introduce some advanced features that can be used for multiple Telnet sessions.

Comments

Post a Comment

Popular posts from this blog

OSI layers / Peer-to-peer communications / TCP/IP model

OSI layers 2.3.4 This page discusses the seven layers of the OSI model. The OSI reference model is a framework that is used to understand how information travels throughout a network. The OSI reference model explains how packets travel through the various layers to another device on a network, even if the sender and destination have different types of network media. In the OSI reference model, there are seven numbered layers, each of which illustrates a particular network function. - Dividing the network into seven layers provides the following advantages: • It breaks network communication into smaller, more manageable parts. • It standardizes network components to allow multiple vendor development and support. • It allows different types of network hardware and software to communicate with each other. • It prevents changes in one layer from affecting other layers. • It divides network communication into smaller parts to make learning it easier to understand. In the foll...
Post a Comment
Read more

PC Basic...

• Backplane – A backplane is an electronic circuit board containing circuitry and sockets into which additional electronic devices on other circuit boards or cards can be plugged; in a computer, generally synonymous with or part of the motherboard. • Network interface card (NIC) – An expansion board inserted into a computer so that the computer can be connected to a network. • Video card – A board that plugs into a PC to give it display capabilities. • Audio card – An expansion board that enables a computer to manipulate and output sounds. • Parallel port – An interface capable of transferring more than one bit simultaneously that is used to connect external devices such as printers. • Serial port – An interface that can be used for serial communication in which only one bit is transmitted at a time. • Mouse port – A port used to connect a mouse to a PC. • USB port – A Universal Serial Bus connector. A USB port connects devices such as a mouse or printer to the computer ...
Post a Comment
Read more

1.2.2 RIP V2 Features

 1.2.2 RIP V2 Features This page will discuss RIP v2, which is an improved version of RIP v1. Both versions of RIP share the following features: It is a distance vector protocol that uses a hop count metric. It uses hold down timers to prevent routing loops – default is 180 seconds. It uses split horizon to prevent routing loops. It uses 16 hops as a metric for infinite distance. RIP v2 provides prefix routing, which allows it to send out subnet mask information with the route update. Therefore, RIP v2 supports the use of classless routing in which different subnets within the same network can use different subnet masks, as in VLSM. RIP v2 provides for authentication in its updates. A set of keys can be used on an interface as an authentication check. RIP v2 allows for a choice of the type of authentication to be used in RIP v2 packets. The choice can be either clear text or Message-Digest 5 (MD5) encryption. Clear text is the default. MD5 can be used t...
Post a Comment
Read more