Skip to main content

Backing up configuration files

Backing up configuration files

3.2.9  This page will teach students how to backup and restore configuration files using tftp.
A current copy of the configuration can be stored on a TFTP server. The copy running-config tftp command can be used to store the current configuration on a network TFTP server, as shown in Figure . To do so, complete the following tasks:
  1. Enter the copy running-config tftp command.
  2. Enter the IP address of the host where the configuration file will be stored.
  3. Enter the name to assign to the configuration file.
  4. Answer yes to confirm each choice.
A configuration file stored on one of the network servers can be used to configure a router. To do so, complete the following tasks:
  1. Use the copy tftp running-config command to enter configuration mode, as shown in Figure .
  2. Select a host or network configuration file at the system prompt. The network configuration file contains commands that apply to all routers and terminal servers on the network. The host configuration file contains commands that apply to one router in particular. At the system prompt, enter the IP address of the remote host where the TFTP server is located. In this example, the router is configured from the TFTP server at IP address 131.108.2.155.
  3. Enter the name of the configuration file or accept the default name. The filename convention is UNIX-based. The default filename is hostname-config for the host file and network-config for the network configuration file. In the DOS environment, filenames are limited to eight characters plus a three-character extension, such as router.cfg. Confirm the configuration filename and the tftp server address that the system supplies. Notice in Figure that the router prompt changes to tokyo immediately. This is evidence that the reconfiguration happens as soon as the new file is downloaded.
To save a router configuration to a disk or hard drive, capture text in the router and save it. If the file needs to be copied back to the router, use the standard edit features of a terminal emulator program to paste the command file into the router.
The Lab Activity on this page will allow students to capture the running configuration of a router.
This page concludes the lesson about router configurations. The next page will summarize the main points from this module.
The next page will explain how configuration files can be copied and implemented. 

Comments

Post a Comment

Popular posts from this blog

OSI layers / Peer-to-peer communications / TCP/IP model

OSI layers 2.3.4 This page discusses the seven layers of the OSI model. The OSI reference model is a framework that is used to understand how information travels throughout a network. The OSI reference model explains how packets travel through the various layers to another device on a network, even if the sender and destination have different types of network media. In the OSI reference model, there are seven numbered layers, each of which illustrates a particular network function. - Dividing the network into seven layers provides the following advantages: • It breaks network communication into smaller, more manageable parts. • It standardizes network components to allow multiple vendor development and support. • It allows different types of network hardware and software to communicate with each other. • It prevents changes in one layer from affecting other layers. • It divides network communication into smaller parts to make learning it easier to understand. In the foll...
Post a Comment
Read more

PC Basic...

• Backplane – A backplane is an electronic circuit board containing circuitry and sockets into which additional electronic devices on other circuit boards or cards can be plugged; in a computer, generally synonymous with or part of the motherboard. • Network interface card (NIC) – An expansion board inserted into a computer so that the computer can be connected to a network. • Video card – A board that plugs into a PC to give it display capabilities. • Audio card – An expansion board that enables a computer to manipulate and output sounds. • Parallel port – An interface capable of transferring more than one bit simultaneously that is used to connect external devices such as printers. • Serial port – An interface that can be used for serial communication in which only one bit is transmitted at a time. • Mouse port – A port used to connect a mouse to a PC. • USB port – A Universal Serial Bus connector. A USB port connects devices such as a mouse or printer to the computer ...
Post a Comment
Read more

1.2.2 RIP V2 Features

 1.2.2 RIP V2 Features This page will discuss RIP v2, which is an improved version of RIP v1. Both versions of RIP share the following features: It is a distance vector protocol that uses a hop count metric. It uses hold down timers to prevent routing loops – default is 180 seconds. It uses split horizon to prevent routing loops. It uses 16 hops as a metric for infinite distance. RIP v2 provides prefix routing, which allows it to send out subnet mask information with the route update. Therefore, RIP v2 supports the use of classless routing in which different subnets within the same network can use different subnet masks, as in VLSM. RIP v2 provides for authentication in its updates. A set of keys can be used on an interface as an authentication check. RIP v2 allows for a choice of the type of authentication to be used in RIP v2 packets. The choice can be either clear text or Message-Digest 5 (MD5) encryption. Clear text is the default. MD5 can be used t...
Post a Comment
Read more