Skip to main content

1.2.2 BOOTP and DHCP differences / 1.2.3 Major DHCP features

1.2.2 BOOTP and DHCP differences

The Internet community first developed the BOOTP protocol to enable configuration of diskless workstations. BOOTP was originally defined in RFC 951 in 1985. As the predecessor of DHCP, BOOTP shares some operational characteristics. Both protocols are client/server based and use UDP ports 67 and 68. Those ports are still known as BOOTP ports.
The four basic IP parameters include:
  • IP address
  • Gateway address
  • Subnet mask
  • DNS server address
BOOTP does not dynamically allocate IP addresses to a host. When a client requests an IP address, the BOOTP server searches a predefined table for an entry that matches the MAC address for the client. If an entry exists, then the corresponding IP address for that entry is returned to the client. This means that the binding between the MAC address and the IP address must have already been configured in the BOOTP server.
There are two primary differences between DHCP and BOOTP:
  • DHCP defines mechanisms through which clients can be assigned an IP address for a finite lease period. This lease period allows for reassignment of the IP address to another client later, or for the client to get another assignment, if the client moves to another subnet. Clients may also renew leases and keep the same IP address.
DHCP provides the mechanism for a client to gather other IP configuration parameters, such as WINS and domain name. 

 1.2.3 Major DHCP features
There are three mechanisms used to assign an IP address to the client:
  • Automatic allocation – DHCP assigns a permanent IP address to a client.
  • Manual allocation – The IP address for the client is assigned by the administrator. DHCP conveys the address to the client.
  • Dynamic allocation – DHCP assigns, or leases, an IP address to the client for a limited period of time.
The focus of this section is the dynamic allocation mechanism. Some of the configuration parameters available are listed in IETF RFC 1533:
  • Subnet mask
  • Router
  • Domain Name
  • Domain Name Server(s)
  • WINS Server(s)
The DHCP server creates pools of IP addresses and associated parameters. Pools are dedicated to an individual logical IP subnet. This allows multiple DHCP servers to respond and IP clients to be mobile. If multiple servers respond, a client can choose only one of the offers.

Comments

Post a Comment

Popular posts from this blog

OSI layers / Peer-to-peer communications / TCP/IP model

OSI layers 2.3.4 This page discusses the seven layers of the OSI model. The OSI reference model is a framework that is used to understand how information travels throughout a network. The OSI reference model explains how packets travel through the various layers to another device on a network, even if the sender and destination have different types of network media. In the OSI reference model, there are seven numbered layers, each of which illustrates a particular network function. - Dividing the network into seven layers provides the following advantages: • It breaks network communication into smaller, more manageable parts. • It standardizes network components to allow multiple vendor development and support. • It allows different types of network hardware and software to communicate with each other. • It prevents changes in one layer from affecting other layers. • It divides network communication into smaller parts to make learning it easier to understand. In the foll...
Post a Comment
Read more

PC Basic...

• Backplane – A backplane is an electronic circuit board containing circuitry and sockets into which additional electronic devices on other circuit boards or cards can be plugged; in a computer, generally synonymous with or part of the motherboard. • Network interface card (NIC) – An expansion board inserted into a computer so that the computer can be connected to a network. • Video card – A board that plugs into a PC to give it display capabilities. • Audio card – An expansion board that enables a computer to manipulate and output sounds. • Parallel port – An interface capable of transferring more than one bit simultaneously that is used to connect external devices such as printers. • Serial port – An interface that can be used for serial communication in which only one bit is transmitted at a time. • Mouse port – A port used to connect a mouse to a PC. • USB port – A Universal Serial Bus connector. A USB port connects devices such as a mouse or printer to the computer ...
Post a Comment
Read more

1.2.2 RIP V2 Features

 1.2.2 RIP V2 Features This page will discuss RIP v2, which is an improved version of RIP v1. Both versions of RIP share the following features: It is a distance vector protocol that uses a hop count metric. It uses hold down timers to prevent routing loops – default is 180 seconds. It uses split horizon to prevent routing loops. It uses 16 hops as a metric for infinite distance. RIP v2 provides prefix routing, which allows it to send out subnet mask information with the route update. Therefore, RIP v2 supports the use of classless routing in which different subnets within the same network can use different subnet masks, as in VLSM. RIP v2 provides for authentication in its updates. A set of keys can be used on an interface as an authentication check. RIP v2 allows for a choice of the type of authentication to be used in RIP v2 packets. The choice can be either clear text or Message-Digest 5 (MD5) encryption. Clear text is the default. MD5 can be used t...
Post a Comment
Read more